00:22:44
The story unfolds with Raja who lives in a small town with his parents and an unmarried sister; Baby Baji. The plot takes a twist when Raja finally musters up the courage to profess his feelings for Meeru but life throws a curve ball at him. The sudden demise of his father that very day leaves Raja with the responsibility of filling in his father’s shoes and also finding a husband for his sister...
: The lock's sensor detects when the door is closed and engages the deadbolt within 5 seconds. Manual Mode
: Users can register a security code ranging from 4 to 12 digits. RFID Card/Key Tags : The lock typically supports up to 20 or more RFID tags. Palm Touch Feature
Rim lock (installs on the inside surface of the door) Authentication: 4 to 12-digit PIN code Power Supply: 4 x 1.5V AA Alkaline batteries (DC 6V) Emergency Power: 9V Alkaline battery (External contacts) Material: Fiberglass and die-cast zinc Door Thickness Compatibility: 35mm to 50mm Gateman V20 Installation Guide
Enter your PIN or tap a registered card to silence the alarm.
Most Gateman locks follow a standard sequence for basic setup. For the V20: : Open the battery cover on the inner body. Press the [I] (Registration) button. Enter your new 4 to 12-digit code on the external keypad. Press the [I] button again to complete. Register Key Tags (Badges) : Press the [I] button inside the unit. gateman v20 manual
To prevent being accidentally locked out, always perform these programming steps while keeping your door wide open! 1. Registering Your Security PIN Code
Plug the cable harness from the external unit into the receiving port on the back of the internal main body. Ensure the connector clicks securely into place.
| Problem | Possible Cause(s) | Solution | | :--- | :--- | :--- | | | Dead batteries | Use the external 9V battery terminal to power the lock and open the door, then replace the internal batteries | | | System freeze or glitch | Locate the small reset pinhole on the interior or exterior panel. Use a paperclip or toothpick to press and hold the reset button for about 10 seconds. This typically reboots the lock | | | Extreme weather conditions | In very cold or hot temperatures, the touch screen or motor may slow down. Wait for a moment and try again | | The door won't lock automatically | Automatic mode is disabled | Re-enable the automatic locking feature via the programming mode or the interior switch | | | Door alignment issues | The strike plate on the door frame may be misaligned. Check if the deadbolt extends smoothly when the door is open. If not, the lock mechanism may be faulty. If it works fine when open, the strike plate likely needs adjustment | | The low battery beep persists | Weak batteries | Even if they are new, try a different brand of high-quality alkaline batteries | | | Dust or debris on the sensor | Clean the keypad and card sensor with a soft, dry cloth | | The lock beeps but the bolt doesn't move | Weak motor due to low batteries | Replace the batteries with new ones | | | Mechanical obstruction | The deadbolt may be blocked by a misaligned door frame. Check and adjust the strike plate | | The RFID card is not recognized | Card is not registered | Re-register the card by following the "Adding a New RFID Card" procedure | | | Damaged card | The RFID chip inside the card may be damaged. Try a different registered card to confirm |
Remove the battery cover. Look for a small toggle switch labeled A/M . Slide it to A for automatic or M for manual. Safety and Advanced Features Fake PIN (Anti-Peeping Function) : The lock's sensor detects when the door
When you are inside, slide the "Double Lock" switch to the red position. This prevents the door from being opened from the outside, even with a valid PIN or card.
Touch the keypad palm with your hand to wake up the screen. Enter your PIN code, then press [*] or touch the screen with your palm again.
Carefully re-type the master PIN. If forgotten, reset the unit via the internal configuration button.
This guide covers the official instructions for setup, daily use, and maintenance. The V20 replaces traditional keys with three primary access methods: Palm Touch Feature Rim lock (installs on the
: Open the battery cover, press the [I] or [R] registration button, enter a new 4–12 digit code on the exterior keypad, and press [I/R] again.
Use a 9V battery for emergency entry, then replace all AA batteries. Door misalignment
Align the strike box on the door frame with the deadbolt. Ensure a 3mm to 5mm gap between the lock body and the strike box when the door is closed. Step-by-Step Programming Guide
Do you need instructions for a not covered here?
